[Fli4l_dev] Verbindungsabbrüche WLAN br43 mastermode

So Mär 10 19:19:27 CET 2013

> a) wieviele andere WLAN-Netze gibt es bei dir in der Umgebung
> b) auf welchen Kanälen arbeiten die
> c) auf welchem Kanal arbeitest du
> d) tritt das Problem auch in anderen AP bzw. Client Kombinationen auf
> e) wie sieht deine Config (Passwort bereinigt) aus
> f) welche Revision nutzt du
> g) welche Karte nutzt du im fli4l
> h) wieviele Antennen hast du an der Karte

Hallo ;)

danke fuers Antworten und sorry wegen dem langen Posting!

Also,

-> zu a: Einige, ich fuerchte aber zu viele, im Client-Mode mehr als 8 
sichtbare SSID's...  ;(

-> zu b: Ich habe alle Kanaele durchprobiert, natuerlich auch die 
Unbelegten, Resultat war aber immer das Gleiche

-> zu c: siehe b., habe wirklich alle durchgeschaltet und eine zeitlang 
laufen lassen

-> zu d: k.A. da kein anderer Fli4l-AP vorhanden, zumindest noch nicht

-> zu e: Wird in den Anhang gepastet

-> zu f: Den neuesten Tarball vom 08.03.'13 mit dem Nonfree-Kernel wegen 
dem AVM-Support

-> zu g: Ich nutze einen externen USB-Stick von TP-Link WN821N v.3.1 
mit einem ath90xx Chipsatz und dem 'ath9k_htc' Treiber im Master-Mode

-> zu h: k.A. vermutlich eine integrierte Antenne im Stick

Installierte OPT's:
fli4l-3.9.0-rev25750, kernel 3.7.10-nonfree
advanced_networking, dns_dhcp
dsl, faxrcv, hd, httpd, isdn, mtgcapri,
usb, wlan, vbox, yaps

Imonc Syslog-Ausgabe:

Info	haveged: haveged Stopping due to signal 15
Info	kernel: device wlan0 left promiscuous mode
Info	kernel: br0: port 1(wlan0) entered disabled state
Info	syslogd exiting
Info	syslogd started: BusyBox v1.21.0
Notiz	kernel: klogd started: BusyBox v1.21.0 (fli4l)
Notiz	kernel: Linux version 3.7.10-nonfree (fli4l at eisler) (gcc version 
4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #1 SMP Thu Feb 28 15:04:20 CET 2013
Info	kernel: KERNEL supported cpus:
Info	kernel:   Intel GenuineIntel
Info	kernel:   AMD AuthenticAMD
Info	kernel:   NSC Geode by NSC
Info	kernel:   Cyrix CyrixInstead
Info	kernel:   Centaur CentaurHauls
Info	kernel:   Transmeta GenuineTMx86
Info	kernel:   Transmeta TransmetaCPU
Info	kernel:   UMC UMC UMC UMC
Info	kernel: e820: BIOS-provided physical RAM map:
Info	kernel: BIOS-e820: [mem 0x0000000000000000-0x000000000009dbff] usable
Info	kernel: BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
Info	kernel: BIOS-e820: [mem 0x0000000000100000-0x0000000006feffff] usable
Info	kernel: BIOS-e820: [mem 0x0000000006ff0000-0x0000000006ffffbf] ACPI 
data
Info	kernel: BIOS-e820: [mem 0x0000000006ffffc0-0x0000000006ffffff] ACPI NVS
Info	kernel: BIOS-e820: [mem 0x00000000fff80000-0x00000000ffffffff] reserved
Info	kernel: init_memory_mapping: [mem 0x00000000-0x06feffff]
Warnung	kernel:   HighMem  empty
Warnung	kernel: Movable zone start for each node
Warnung	kernel: Early memory node ranges
Info	kernel: PID hash table entries: 512 (order: -1, 2048 bytes)
Info	kernel: uhci_hcd 0000:00:10.2: found PCI INT C -> IRQ 3
Info	kernel: uhci_hcd 0000:00:10.2: sharing IRQ 3 with 0000:00:11.5
Info	kernel: uhci_hcd 0000:00:10.2: UHCI Host Controller
Info	kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus 
number 3
Info	kernel: uhci_hcd 0000:00:10.2: irq 10, io base 0x00001240
Info	kernel: usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
Info	kernel: usb usb3: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
Info	kernel: usb usb3: Product: UHCI Host Controller
Info	kernel: usb usb3: Manufacturer: Linux 3.7.10-nonfree uhci_hcd
Info	kernel: usb usb3: SerialNumber: 0000:00:10.2
Info	kernel: hub 3-0:1.0: USB hub found
Info	kernel: hub 3-0:1.0: 2 ports detected
Info	kernel: usbcore: registered new interface driver usbhid
Info	kernel: usbhid: USB HID core driver
Info	kernel: ieee80211 phy0: Atheros AR9287 Rev:2
Info	kernel: cfg80211: Calling CRDA for country: CN
Info	kernel: cfg80211: Regulatory domain changed to country: CN
Info	kernel: cfg80211:   (start_freq - end_freq @ bandwidth), 
(max_antenna_gain, max_eirp)
Info	kernel: cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 
2000 mBm)
Info	kernel: cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 
3000 mBm)
Info	kernel: cfg80211: Calling CRDA for country: DE
Info	kernel: cfg80211: Regulatory domain changed to country: DE
Info	kernel: cfg80211:   (start_freq - end_freq @ bandwidth), 
(max_antenna_gain, max_eirp)
Info	kernel: cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 
2000 mBm)
Info	kernel: cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 
2000 mBm)
Info	kernel: cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 
2000 mBm)
Info	kernel: cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 
2698 mBm)
Info	kernel: device wlan0 entered promiscuous mode
Info	kernel: IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Info	kernel: IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Info	kernel: PPP generic driver version 2.4.2
Notiz	kernel: ISDN subsystem Rev: 
1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
Notiz	kernel: CAPI 2.0 started up with major 68 (middleware)
Warnung	kernel: fcusb2: module license 'Proprietary' taints kernel.
Warnung	kernel: Disabling lock debugging due to kernel taint
Info	kernel: fcusb2: AVM FRITZ!Card USB v2 driver, revision 0.6.4
Info	kernel: fcusb2: -- 32 bit CAPI driver --
Info	kernel: fcusb2: Loading...
Warnung	kernel: <6>fcusb2: Driver 'fcusb2' attached to fcusb2-stack. (152)
Info	kernel: NET: Registered protocol family 24
Info	kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Info	kernel: nf_conntrack version 0.5.0 (1710 buckets, 6840 max)
Info	pppd[6072]: Plugin rp-pppoe.so loaded.
Notiz	pppd[6072]: pppd 2.4.5 started by root, uid 0
Info	pppd[6072]: PPP session is 1043
Warnung	pppd[6072]: Connected to 00:90:1a:41:ef:0b via interface eth0.7
Info	pppd[6072]: Using interface ppp0
Notiz	pppd[6072]: Connect: ppp0 <--> eth0.7
Notiz	pppd[6072]: PAP authentication succeeded
Notiz	pppd[6072]: peer from calling number 00:90:1A:41:EF:0B authorized
Notiz	pppd[6072]: local  IP address 217.246.45.252
Notiz	pppd[6072]: remote IP address 217.0.119.203
Notiz	pppd[6072]: primary   DNS address 217.0.43.49
Notiz	pppd[6072]: secondary DNS address 217.0.43.33
Notiz	ip-up[6296]: starting (ppp0 eth0.7 0 217.246.45.252 217.0.119.203)...
Info	dnsmasq[6572]: started, version 2.65 cachesize 150
Info	dnsmasq[6572]: compile time options: IPv6 GNU-getopt no-DBus 
no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP conntrack
Info	dnsmasq[6572]: using local addresses only for domain Flisystem
Info	dnsmasq[6572]: using local addresses only for domain 
168.192.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
31.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
30.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
29.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
28.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
27.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
26.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
25.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
24.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
23.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
22.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
21.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
20.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
19.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
18.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
17.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
16.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 10.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 127.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain Flisystem
Info	dnsmasq[6572]: read /etc/hosts - 3 addresses
Info	dnsmasq[6572]: read /etc/hosts.d/dhcp.hosts - 0 addresses
Info	dnsmasq[6572]: read /etc/hosts.d/hosts.global - 0 addresses
Info	dnsmasq[6572]: read /etc/hosts.d/hosts.dns - 3 addresses
Info	dnsmasq[6572]: using nameserver 194.8.57.8#53
Info	dnsmasq[6572]: using local addresses only for domain Flisystem
Info	dnsmasq[6572]: using local addresses only for domain 
168.192.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
31.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
30.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
29.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
28.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
27.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
26.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
25.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
24.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
23.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
22.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
21.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
20.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
19.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
18.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
17.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
16.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 10.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 127.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain Flisystem
Info	imond[6605]: setting default route to circuit 'VDSL'
Notiz	add-default-route: adding route for pppoe
Info	telmond[6591]: 1 controller available.
Info	telmond[6591]: Listening for events on controller 1.
Notiz	add-default-route: ip route add default dev ppp0
Info	telmond[6591]: LISTEN_CONF received for controller 1.
Notiz	setup-portfw.sh: create
Notiz	setup-portfw.sh: up static
Warnung	mini_httpd[6766]: started as root without requesting chroot(), 
warning only
Notiz	mini_httpd[6766]: mini_httpd/1.19-fli4l 2012-02-21 starting on 
Fli4l, port 80
Info	capifaxrcvd[6802]: Start listening
Info	kernel: br0: port 1(wlan0) entered forwarding state
Info	kernel: br0: port 2(eth1) entered forwarding state
Notiz	ip-up[6296]:    executing ip-up scripts ...
Notiz	ip-up[6296]: default route interface 'pppoe' comes up
Notiz	ip-up[6296]: changing default route from <none>:ppp0 to <none>:pppoe
Notiz	ip-up[6296]: executing /etc/ppp/ip-up200.dns
Info	dnsmasq[6572]: read /etc/hosts - 3 addresses
Info	dnsmasq[6572]: read /etc/hosts.d/dhcp.hosts - 0 addresses
Info	dnsmasq[6572]: read /etc/hosts.d/hosts.global - 0 addresses
Info	dnsmasq[6572]: read /etc/hosts.d/hosts.dns - 3 addresses
Info	dnsmasq[6572]: using nameserver 217.0.43.33#53
Info	dnsmasq[6572]: using nameserver 217.0.43.49#53
Info	dnsmasq[6572]: using local addresses only for domain Flisystem
Info	dnsmasq[6572]: using local addresses only for domain 
168.192.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
31.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
30.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
29.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
28.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
27.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
26.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
25.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
24.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
23.172.in-addr.arpa
Notiz	ip-up[6296]: executing /etc/ppp/ip-up300.logip
Info	dnsmasq[6572]: using local addresses only for domain 
22.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
21.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
20.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
19.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
18.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
17.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 
16.172.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 10.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain 127.in-addr.arpa
Info	dnsmasq[6572]: using local addresses only for domain Flisystem
Notiz	ip-up[6296]: executing /etc/ppp/ip-up400.portfw
Notiz	ip-up[6296]: port forwarding: switching to dynamic rule set ...
Notiz	ip-up[6296]: setup-portfw.sh: up dynamic 217.246.45.252
Notiz	setup-portfw.sh: up dynamic 217.246.45.252
Notiz	ip-up[6296]: port forwarding: done
Notiz	ip-up[6296]: executing /etc/ppp/ip-up900.user
Notiz	ip-up[6296]:    finished ip-up scripts ...
Notiz	ip-up[6296]: terminating ...
Info	hostapd: wlan0: STA 18:00:2d:b5:67:80 IEEE 802.11: authenticated
Info	hostapd: wlan0: STA 18:00:2d:b5:67:80 IEEE 802.11: associated (aid 1)
Info	hostapd: wlan0: STA 18:00:2d:b5:67:80 RADIUS: starting accounting 
session 513CC563-00000000
Info	hostapd: wlan0: STA 18:00:2d:b5:67:80 WPA: pairwise key handshake 
completed (RSN)
Info	hostapd: wlan0: STA 18:00:2d:b5:67:80 WPA: group key handshake 
completed (RSN)

HTTPD-Bootlog:

rootfs on / type rootfs (rw)
tmpfs on / type tmpfs (rw,relatime,size=53756k,nr_inodes=13439,mode=755)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
running boot scripts
basic setup for booting... (/etc/boot.d/rc000.base)
Wrapping of modutils disabled ()
finished basic setup for booting... (/etc/boot.d/rc000.base)
loading USB core drivers ... (/etc/boot.d/rc005.usb)
finished loading USB core drivers ... (/etc/boot.d/rc005.usb)
loading disk drivers ... (/etc/boot.d/rc010.hddrv)
finished loading disk drivers ... (/etc/boot.d/rc010.hddrv)
loading generic disk drivers ... (/etc/boot.d/rc020.hd-generic)
finished loading generic disk drivers ... (/etc/boot.d/rc020.hd-generic)
loading USB storage drivers ... (/etc/boot.d/rc030.usb)
finished loading USB storage drivers ... (/etc/boot.d/rc030.usb)
waiting for USB bus initial emumeration ... (/etc/boot.d/rc030.usb)
Waiting for USB bus to settle up.
finished waiting for USB bus initial emumeration ... (/etc/boot.d/rc030.usb)
scanning for partition tables on storage ... (/etc/boot.d/rc040.partitions)
sda: sda1 sda2 sda3
finished scanning for partition tables on storage ... 
(/etc/boot.d/rc040.partitions)
mounting boot device ... (/etc/boot.d/rc100.hdboot)
dosfsck 3.0.16, 01 Mar 2013, FAT32, LFN
/dev/sda1: 14 files, 3003/51283 clusters
finished mounting boot device ... (/etc/boot.d/rc100.hdboot)
unpacking opt new archive ... (/etc/boot.d/rc100.hdboot)
/dev/sda2: clean, 487/25792 files, 15610/102816 blocks
extracting files from opt archive
........
finished unpacking opt new archive ... (/etc/boot.d/rc100.hdboot)
integrating mounted opt partition ... (/etc/boot.d/rc100.hdboot)
finished integrating mounted opt partition ... (/etc/boot.d/rc100.hdboot)
finished boot scripts
boot_dev=/dev/sda1
boot_fs=vfat
hd_data=sda3
checking for known problems ... (/etc/rc.d/rc000._bug)
finished checking for known problems ... (/etc/rc.d/rc000._bug)
basic setup... (/etc/rc.d/rc000.base)
finished basic setup... (/etc/rc.d/rc000.base)
creating /etc/resolv.conf and /etc/hosts ... (/etc/rc.d/rc001.base)
writing /etc/resolv.conf ...
writing /etc/hosts ...
finished creating /etc/resolv.conf and /etc/hosts ... (/etc/rc.d/rc001.base)
creating hosts-files .... (/etc/rc.d/rc001.hosts)
writing HOSTS to /etc/hosts.d/hosts.dns ...
finished creating hosts-files .... (/etc/rc.d/rc001.hosts)
loading USB drivers ... (/etc/rc.d/rc005.usb)
now waiting for the drivers to come up
finished loading USB drivers ... (/etc/rc.d/rc005.usb)
mounting other partitions ... (/etc/rc.d/rc030.mount)
mounting data-partition...
/dev/sda3: clean, 69/98784 files, 7646/197316 blocks
mounting cd-rom...
finished mounting other partitions ... (/etc/rc.d/rc030.mount)
preparing IPv6... (/etc/rc.d/rc050.ipv6)
finished preparing IPv6... (/etc/rc.d/rc050.ipv6)
starting haveged ... (/etc/rc.d/rc090.haveged)
Mar 10 18:39:40 haveged: haveged starting up
finished starting haveged ... (/etc/rc.d/rc090.haveged)
preparing bridge devices... (/etc/rc.d/rc100.bridge)
finished preparing bridge devices... (/etc/rc.d/rc100.bridge)
executing WLAN_MAC80211 (/etc/rc.d/rc110.wlan)
finished executing WLAN_MAC80211 (/etc/rc.d/rc110.wlan)
loading network drivers ... (/etc/rc.d/rc120.net)
finished loading network drivers ... (/etc/rc.d/rc120.net)
executing WLAN (/etc/rc.d/rc130.wlan)
configuring wlan on wlan0 ...
Configuration file: /etc/hostapd.wlan0
Using interface wlan0 with hwaddr xx:xx:xx:xx:xx:xx and ssid "Flisystem"
finished executing WLAN (/etc/rc.d/rc130.wlan)
configuring isdn ... (/etc/rc.d/rc220.i4l)
Loading Bootcode /usr/lib/isdn/fus3base.frm ... done
Verbose-level set to 2.
finished configuring isdn ... (/etc/rc.d/rc220.i4l)
setting up vlan devices... (/etc/rc.d/rc250.vlan)
finished setting up vlan devices... (/etc/rc.d/rc250.vlan)
setting up bridge devices... (/etc/rc.d/rc300.bridge)
Skipping Device wlan0 as already member of a bridge
finished setting up bridge devices... (/etc/rc.d/rc300.bridge)
configuring loopback and ethernet device ... (/etc/rc.d/rc300.lo)
finished configuring loopback and ethernet device ... (/etc/rc.d/rc300.lo)
configuring syslogd for telmond ... (/etc/rc.d/rc300.telmond-syslog)
finished configuring syslogd for telmond ... 
(/etc/rc.d/rc300.telmond-syslog)
configuring ip on network cards ... (/etc/rc.d/rc305.ip-eth)
finished configuring ip on network cards ... (/etc/rc.d/rc305.ip-eth)
starting syslogd ... (/etc/rc.d/rc325.syslogd)
finished starting syslogd ... (/etc/rc.d/rc325.syslogd)
starting klogd ... (/etc/rc.d/rc330.klogd)
finished starting klogd ... (/etc/rc.d/rc330.klogd)
configure logip ... (/etc/rc.d/rc335.logip)
finished configure logip ... (/etc/rc.d/rc335.logip)
preparing circuits ... (/etc/rc.d/rc340.circuits)
writing /etc/ppp/pap-secrets ...
finished preparing circuits ... (/etc/rc.d/rc340.circuits)
starting pppoe ... (/etc/rc.d/rc340.circuits.pppoe_in_kernel)
finished starting pppoe ... (/etc/rc.d/rc340.circuits.pppoe_in_kernel)
configuring firewall ... (/etc/rc.d/rc360.fwrules)
finished configuring firewall ... (/etc/rc.d/rc360.fwrules)
configure DNS service... (/etc/rc.d/rc370.dns_dhcp)
Plugin rp-pppoe.so loaded.
PPP session is 1043
Connected to 00:90:1a:41:ef:0b via interface eth0.7
Using interface ppp0
Connect: ppp0 <--> eth0.7
PAP authentication succeeded
peer from calling number xx:xx:xx:xx:xx:xx authorized
local IP address xx
remote IP address xx
primary DNS address xx
secondary DNS address xx
finished configure DNS service... (/etc/rc.d/rc370.dns_dhcp)
start dnsmasq as DNS server ... (/etc/rc.d/rc390.dns_dhcp)
finished start dnsmasq as DNS server ... (/etc/rc.d/rc390.dns_dhcp)
starting telmond ... (/etc/rc.d/rc400.telmond)
finished starting telmond ... (/etc/rc.d/rc400.telmond)
starting imond ... (/etc/rc.d/rc405.imond)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
--------------------------------------------------------------------------
Su 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Mo 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Tu 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
We 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Th 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Fr 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Sa 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

No. Name LCR DRoute Device Ch/Min ChInt
1 VDSL yes yes pppoe 0.0000 60
Mo-Su 00-24 pppoe -1:-1 0 yes yes - VDSL 0.0 60 pppoe
finished starting imond ... (/etc/rc.d/rc405.imond)
setting up static port forwarding ... (/etc/rc.d/rc425.portfw)
creating rule sets
setup-portfw.sh: create
setting up rule sets
setup-portfw.sh: up static
finished setting up static port forwarding ... (/etc/rc.d/rc425.portfw)
Starting webserver ... (/etc/rc.d/rc430.httpd)
finished Starting webserver ... (/etc/rc.d/rc430.httpd)
/usr/sbin/mini_httpd: started as root without requesting chroot(), 
warning only
configuring capifaxrcvd ... (/etc/rc.d/rc500.faxrcv)
starting capifaxrcvd (ID: 1, MSN: xxxxxx) ...
finished configuring capifaxrcvd ... (/etc/rc.d/rc500.faxrcv)
Starting mtG-CAPRI-Server ... (/etc/rc.d/rc900.mtgcapri)
finished Starting mtG-CAPRI-Server ... (/etc/rc.d/rc900.mtgcapri)
finishing boot process ... (/etc/rc.d/rc998.base)
finished finishing boot process ... (/etc/rc.d/rc998.base)
terminating bootlogd to close bootlog ...

Config aus der HTTPD Support-Sektion:

# generated by mkfli4l (Revision: 25249)
#
# package 'base'
#
AUTO='99'
BASE='yes'
HOSTNAME='Fliserver'
PASSWORD='xxxx'
BOOT_TYPE='hd'
LIBATA_NODMA='yes'
MOUNT_BOOT='rw'
BOOTMENU_TIME='5'
TIME_INFO='MEZ-1MESZ,M3.5.0,M10.5.0/3'
KERNEL_VERSION='3.7.10-nonfree'
KERNEL_BOOT_OPTION=''
COMPRESS_ROOTFS='yes'
COMPRESS_OPT='yes'
COMP_TYPE_OPT='xz'
IP_CONNTRACK_MAX=''
POWERMANAGEMENT='none'
LOCALE='de'
CONSOLE_BLANK_TIME=''
BEEP='no'
SER_CONSOLE='no'
DEBUG_STARTUP='no'
KEYBOARD_LOCALE='auto'
NET_DRV_N='3'
NET_DRV_1='3c59x'
NET_DRV_1_OPTION=''
NET_DRV_2='via-rhine'
NET_DRV_2_OPTION=''
NET_DRV_3='ath9k_htc'
NET_DRV_3_OPTION=''
IP_NET_N='1'
IP_NET_1='192.168.6.1/24'
IP_NET_1_DEV='br0'
IP_ROUTE_N='0'
PF_INPUT_POLICY='REJECT'
PF_INPUT_ACCEPT_DEF='yes'
PF_INPUT_LOG='no'
PF_INPUT_LOG_LIMIT='3/minute:5'
PF_INPUT_REJ_LIMIT='1/second:5'
PF_INPUT_UDP_REJ_LIMIT='1/second:5'
PF_INPUT_N='1'
PF_INPUT_1='IP_NET_1 ACCEPT'
PF_FORWARD_POLICY='REJECT'
PF_FORWARD_ACCEPT_DEF='yes'
PF_FORWARD_LOG='no'
PF_FORWARD_LOG_LIMIT='3/minute:5'
PF_FORWARD_REJ_LIMIT='1/second:5'
PF_FORWARD_UDP_REJ_LIMIT='1/second:5'
PF_FORWARD_N='2'
PF_FORWARD_1='tmpl:samba DROP'
PF_FORWARD_2='IP_NET_1 ACCEPT'
PF_POSTROUTING_N='1'
PF_POSTROUTING_1='IP_NET_1 MASQUERADE'
PF_PREROUTING_N='0'
PF_USR_CHAIN_N='0'
PORTFW_N='0'
MASQ_MODULE_N='0'
DOMAIN_NAME='Flisystem'
DNS_FORWARDERS='194.8.57.8'
START_IMOND='yes'
IMOND_PORT='5000'
IMOND_PASS='xxxx'
IMOND_ADMIN_PASS='xxxx'
IMOND_LED=''
IMOND_BEEP='no'
IMOND_LOG='no'
IMOND_LOGDIR='/data/log/imond.log'
IMOND_ENABLE='yes'
IMOND_DIAL='yes'
IMOND_ROUTE='yes'
IMOND_REBOOT='yes'
IP_DYN_ADDR='yes'
DIALMODE='auto'
OPT_SYSLOGD='yes'
SYSLOGD_RECEIVER='yes'
SYSLOGD_DEST_N='1'
SYSLOGD_DEST_1='*.* @192.168.6.5'
SYSLOGD_ROTATE='no'
OPT_KLOGD='yes'
OPT_LOGIP='yes'
LOGIP_LOGDIR='/data/log'
#
# package 'dns_dhcp'
#
HOST_N='3'
HOST_1_NAME='W7_Client'
HOST_1_IP4='192.168.6.5'
HOST_1_ALIAS_N='0'
HOST_2_NAME='tablet'
HOST_2_IP4='192.168.6.11'
HOST_2_MAC='xxx'
HOST_3_NAME='xperia'
HOST_3_IP4='192.168.6.8'
HOST_3_MAC='xxxx'
HOST_EXTRA_N='0'
OPT_DNS='yes'
DNS_LISTENIP_N='0'
DNS_VERBOSE='no'
DNS_MX_SERVER=''
DNS_FORBIDDEN_N='0'
DNS_REDIRECT_N='0'
DNS_BOGUS_PRIV='yes'
DNS_FILTERWIN2K='no'
DNS_SPECIAL_N='0'
DNS_REBINDOK_N='0'
#
# package 'advanced_networking'
#
OPT_BRIDGE_DEV='yes'
BRIDGE_DEV_N='1'
BRIDGE_DEV_1_NAME='netzwlan'
BRIDGE_DEV_1_DEVNAME='br0'
BRIDGE_DEV_1_DEV_N='2'
BRIDGE_DEV_1_DEV_1_DEV='eth1'
BRIDGE_DEV_1_DEV_2_DEV='wlan0'
OPT_VLAN_DEV='yes'
VLAN_DEV_N='1'
VLAN_DEV_1_DEV='eth0'
VLAN_DEV_1_VID='7'
DEV_MTU_N='0'
#
# package 'dsl'
#
OPT_PPPOE='yes'
PPPOE_NAME='VDSL'
PPPOE_USEPEERDNS='yes'
PPPOE_ETH='eth0.7'
PPPOE_TYPE='in_kernel'
PPPOE_DEBUG='no'
PPPOE_USER='xxxx'
PPPOE_PASS='xxxx'
PPPOE_HUP_TIMEOUT='never'
PPPOE_CHARGEINT='60'
PPPOE_TIMES='Mo-Su:00-24:0.0:Y'
PPPOE_FILTER='yes'
PPPOE_FILTER_EXPR=''
PPPOE_MTU='1492'
PPPOE_MRU='1492'
#
# package 'faxrcv'
#
OPT_FAXRCV='yes'
FAXRCV_START_AT_BOOT='yes'
FAXRCV_N='1'
FAXRCV_1_CSID='+49(00)-2xxxx'
FAXRCV_1_NUMBER='xxxx'
FAXRCV_1_DIRECTORY='/data/fax'
FAXRCV_1_NTFYCMD_N='0'
FAXRCV_IMONC_LIST='1'
OPT_FAXRCV_HTTPGUI='yes'
FAXRCV_HTTPGUI_CONVERT='yes'
#
# package 'hd'
#
OPT_HDDRV='yes'
HDDRV_N='0'
OPT_MOUNT='yes'
OPT_EXTMOUNT='no'
#
# package 'httpd'
#
OPT_HTTPD='yes'
HTTPD_PORT='80'
HTTPD_USER_N='xxxx'
HTTPD_USER_1_USERNAME='xxxx'
HTTPD_USER_1_PASSWORD='xxxx'
HTTPD_USER_1_RIGHTS='xxxx'
HTTPD_GUI_LANG='auto'
HTTPD_GUI_SKIN='default'
HTTPD_ARPING='no'
#
# package 'isdn'
#
OPT_ISDN='yes'
ISDN_TYPE='109'
ISDN_IO=''
ISDN_IO0=''
ISDN_IO1=''
ISDN_MEM=''
ISDN_IRQ=''
ISDN_DEBUG_LEVEL='31'
ISDN_VERBOSE_LEVEL='2'
ISDN_FILTER='yes'
ISDN_FILTER_EXPR=''
OPT_ISDN_COMP='yes'
ISDN_LZS_DEBUG='1'
ISDN_LZS_COMP='8'
ISDN_LZS_TWEAK='7'
ISDN_CIRC_N='0'
OPT_TELMOND='yes'
TELMOND_PORT='5001'
TELMOND_LOG='yes'
TELMOND_LOGDIR='/data/log'
TELMOND_MSN_N='3'
TELMOND_MSN_1='xxxx 192.168.6.5'
TELMOND_MSN_2='xxxx 192.168.6.5'
TELMOND_MSN_3='xxxx 192.168.6.5'
TELMOND_CMD_N='0'
TELMOND_CAPI_CTRL_N='0'
#
# package 'mtgcapri'
#
OPT_MTGCAPRI='yes'
MTGCAPRI_PORT='20000'
MTGCAPRI_TRACELEVEL='0'
MTGCAPRI_TRACEFILE='/data/log/capri.trc'
MTGCAPRI_LOGFILE='/data/log/caprilog.txt'
MTGCAPRI_MULTIPLEBIND='yes'
MTGCAPRI_USER_N='xxxx'
MTGCAPRI_USER_1_NAME='xxxx'
MTGCAPRI_USER_1_SERVICE='xxxx'
MTGCAPRI_USER_1_OWN_NUMBERS='xxxx'
MTGCAPRI_USER_1_OWN_NUMBERS_LIST='xxxx'
MTGCAPRI_USER_1_INCOMING_NUMBERS='xxxx'
MTGCAPRI_USER_1_INCOMING_NUMBERS_LIST='xxxx'
MTGCAPRI_USER_1_OUTGOING_NUMBERS='xxxx'
MTGCAPRI_USER_1_OUTGOING_NUMBERS_LIST='xxxx'
MTGCAPRI_USER_1_TIME_MO='xxxx'
MTGCAPRI_USER_1_TIME_DI='xxxx'
MTGCAPRI_USER_1_TIME_MI='xxxx'
MTGCAPRI_USER_1_TIME_DO='xxxx'
MTGCAPRI_USER_1_TIME_FR='xxxx'
MTGCAPRI_USER_1_TIME_SA='xxxx'
MTGCAPRI_USER_1_TIME_SO='xxxx'
MTGCAPRI_USER_2_NAME='xxxx'
MTGCAPRI_USER_2_SERVICE='xxxx'
MTGCAPRI_USER_2_OWN_NUMBERS='xxxx'
MTGCAPRI_USER_2_OWN_NUMBERS_LIST='xxxx'
MTGCAPRI_USER_2_INCOMING_NUMBERS='xxxx'
MTGCAPRI_USER_2_INCOMING_NUMBERS_LIST='xxxx'
MTGCAPRI_USER_2_OUTGOING_NUMBERS='xxxx'
MTGCAPRI_USER_2_OUTGOING_NUMBERS_LIST='xxxx'
MTGCAPRI_USER_2_TIME_MO='xxxx'
MTGCAPRI_USER_2_TIME_DI='xxxx'
MTGCAPRI_USER_2_TIME_MI='xxxx'
MTGCAPRI_USER_2_TIME_DO='xxxx'
MTGCAPRI_USER_2_TIME_FR='xxxx'
MTGCAPRI_USER_2_TIME_SA='xxxx'
MTGCAPRI_USER_2_TIME_SO='xxxx'
#
# package 'usb'
#
OPT_USB='yes'
USB_EXTRA_DRIVER_N='0'
#
# package 'wlan'
#
OPT_WLAN='yes'
WLAN_REGDOMAIN='DE'
WLAN_WEBGUI='yes'
WLAN_N='1'
WLAN_1_MAC='54:E6:FC:89:33:78'
WLAN_1_ESSID='testwlan'
WLAN_1_MODE='master'
WLAN_1_CHANNEL='13g'
WLAN_1_RATE='auto'
WLAN_1_ENC_N='0'
WLAN_1_WPA_KEY_MGMT='WPA-PSK'
WLAN_1_WPA_PSK='xxxx'
WLAN_1_WPA_TYPE='2'
WLAN_1_WPA_ENCRYPTION='CCMP'
WLAN_1_ACL_POLICY='open'
WLAN_1_ACL_MAC_N='0'
WLAN_1_WPS='no'
#
# package 'base'
#
LIBC_VERSION='0.9.33'
LOG_BOOT_SEQ='yes'
OPT_MAKEKBL='no'
OPT_DMZ='no'
PF_INPUT_ICMP_ECHO_REQ_SIZE='150'
OPT_Y2K='no'
OPT_PNP='no'
OPT_ADDMODULES='no'
OPT_EVSS='no'
COMP_TYPE_ROOTFS='xz'
FLI4L_BUILDDIR='D:\System\fli4l-3.9.0-rev26326-testing\config'
FLI4L_BUILDDATE='2013-03-10'
FLI4L_BUILDTIME='18:36:20'
FLI4L_VERSION='3.9.0-rev26326-testing'
#
# package 'dns_dhcp'
#
OPT_HOSTS='yes'
DNS_FORWARD_LOCAL='no'
OPT_DHCP='no'
OPT_DHCPRELAY='no'
OPT_TFTP='no'
#
# package 'advanced_networking'
#
OPT_EBTABLES='no'
OPT_BONDING_DEV='no'
OPT_ETHTOOL='no'
OPT_IPSET='no'
#
# package 'dsl'
#
PPPD_VERSION='2.4.5'
OPT_FRITZDSL='no'
OPT_PPTP='no'
OPT_POESTATUS='no'
#
# package 'faxrcv'
#
OPT_OLED_DIRBLINK='no'
OPT_CAPIFAXBLINK='no'
#
# package 'hd'
#
OPT_HDINSTALL='no'
OPT_HDSLEEP='no'
OPT_RECOVER='no'
OPT_HDINSTALL_TEST='no'
#
# package 'httpd'
#
HTTPD_PORTFW='yes'
OPT_GUI_CONFIG='no'
OPT_OAC='no'
#
# package 'isdn'
#
OPT_RCAPID='no'
#
# package 'kernel_3_7_nonfree'
#
COMP_TYPE_ROOTFS_3_7_NONFREE='xz'
#
# package 'base'
#
KERNEL_MAJOR='3.7'
FLI4L_MD5_RC_CFG='41400d38a51d93250c1c7d2a945e48a8'
FLI4L_MD5_KERNEL='0ac39b480c87068a480b5e85b43c9ebf'
FLI4L_MD5_ROOTFS_IMG='547d8b4d709cfa58251623a7e3d9cb25'
FLI4L_MD5_OPT_IMG='c0414abceaccc197ba943c61415d11a2'
FLI4L_MD5_SYSLINUX_CFG='95773fe1c9594ee7f7380e765b5bba87'