[fli4l] 2 Wlan Dev aber nu?==?utf-8?Q?r wlan0 existiert/wird gef?==?utf-8?Q?unden

[Marc-Oliver Lange]

Hi,
ich habe die Fli4l 4.0 Version am laufen und versuche gerade bei meinem
APU2 einen zweiten WLan USB Stick (DWL-G122 C1) ans laufen zu bringen.
(Möchte gerne hier die Möglichkeit von 2.4 und 5 GHz haben)

In der Base habe ich folgende eingetragen:

NET_DRV[]='igb'           # 1st driver: name (e.g. NE2000 PCI clone)
{
  OPTION=''                    # 1st driver: additional option
}
NET_DRV[]='ath10k_pci'                 # 2nd driver: name (e.g. NE2000
ISA clone)
{
  OPTION=''            # 2nd driver: additional option
}
NET_DRV[]='rt2500usb'                 # 2nd driver: name (e.g. NE2000
ISA clone)
{
  OPTION=''            # 2nd driver: additional option
}

In der advanced_networking

OPT_BRIDGE_DEV='yes'            # activate Bridging 802.1D, yes or no
BRIDGE_DEV_N='1'
BRIDGE_DEV_1_NAME='MyBrigde'
BRIDGE_DEV_1_DEVNAME='br0'
BRIDGE_DEV_1_DEV_N='4'
BRIDGE_DEV_1_DEV_1_DEV='wlan0'
BRIDGE_DEV_1_DEV_2_DEV='wlan1'
BRIDGE_DEV_1_DEV_3_DEV='eth0'
BRIDGE_DEV_1_DEV_4_DEV='eth2'

Aber im Bootlog habe das folgenden stehen:

Sat Oct 29 12:48:17 2016: + brctl addif br0 wlan1
Sat Oct 29 12:48:17 2016: interface wlan1 does not exist!
Sat Oct 29 12:48:17 2016: + ip addr flush dev wlan1
Sat Oct 29 12:48:17 2016: Device "wlan1" does not exist.
Sat Oct 29 12:48:17 2016: + ip link set dev wlan1 up
Sat Oct 29 12:48:17 2016: Cannot find device "wlan1"


lsmod -vv zeigt mir aber das device an:
Bus 001 Device 003: ID 07d1:3c03 D-Link System AirPlus G DWL-G122
Wireless Adapter(rev.C1) [Ralink RT2571W]
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x07d1 D-Link System
  idProduct          0x3c03 AirPlus G DWL-G122 Wireless Adapter(rev.C1)
[Ralink RT2571W]
  bcdDevice            0.01
  iManufacturer           1 Ralink
  iProduct                2 802.11 bg WLAN
  iSerial                 0
  bNumConfigurations      1

und dmseg ergibt zu guter letzt dieses hier:

igb 0000:03:00.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s)
ath10k_pci 0000:04:00.0: pci irq msi interrupts 1 irq_mode 0 reset_mode
0
ath10k_pci 0000:04:00.0: Direct firmware load for
ath10k/cal-pci-0000:04:00.0.bin failed with error -2
ath10k_pci 0000:04:00.0: Direct firmware load for
ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
ath10k_pci 0000:04:00.0: qca988x hw2.0 (0x4100016c, 0x043222ff sub
0000:0000) fw 10.2.4.70.9-2 fwapi 5 bdapi 1 htt-ver 2.1 wmi-op 5 htt-op
2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,raw-mode
ath10k_pci 0000:04:00.0: debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
cfg80211: Regulatory domain changed to country: US
cfg80211:  DFS Master region: FCC
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp), (dfs_cac_time)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm),
(N/A)
cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO),
(N/A, 2300 mBm), (N/A)
cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO),
(N/A, 2300 mBm), (0 s)
cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm),
(0 s)
cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm),
(N/A)
cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000
mBm), (N/A)
usbcore: registered new interface driver rt2500usb
cfg80211: Regulatory domain changed to country: DE
cfg80211:  DFS Master region: ETSI
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp), (dfs_cac_time)
cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm),
(N/A)
cfg80211:   (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO),
(N/A, 2000 mBm), (N/A)
cfg80211:   (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO),
(N/A, 2000 mBm), (0 s)
cfg80211:   (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2698 mBm),
(0 s)
cfg80211:   (5725000 KHz - 5875000 KHz @ 80000 KHz), (N/A, 1397 mBm),
(N/A)
cfg80211:   (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000
mBm), (N/A)
device wlan0 entered promiscuous mode
br0: port 1(wlan0) entered forwarding state
br0: port 1(wlan0) entered forwarding state
device eth0 entered promiscuous mode
device eth2 entered promiscuous mode
igb 0000:01:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX
br0: port 2(eth0) entered forwarding state
br0: port 2(eth0) entered forwarding state
igb 0000:03:00.0 eth2: igb: eth2 NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX/TX
br0: port 3(eth2) entered forwarding state
br0: port 3(eth2) entered forwarding state
br0: port 1(wlan0) entered forwarding state
br0: port 2(eth0) entered forwarding state
br0: port 3(eth2) entered forwarding state
PPP generic driver version 2.4.2
NET: Registered protocol family 24
igb 0000:02:00.0 eth1: igb: eth1 NIC Link is Up 100 Mbps Full Duplex,
Flow Control: RX
i2c /dev entries driver
Adjusting tsc more than 11% (7355774 vs 9328827)
usb 1-1: USB disconnect, device number 2
usb 1-1: new high-speed USB device number 3 using xhci_hcd
usb 1-1: New USB device found, idVendor=07d1, idProduct=3c03
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: 802.11 bg WLAN
usb 1-1: Manufacturer: Ralink


Was übersehe ich? 
VG und danke 
Marco