[Eisfair] IP Zuordung der Netzwerkkarten nach letztem Kernelupdate getauscht

[Nils Lange]

Hallo Marcus,

On 05.11.2016 22:57, Marcus Roeckrath wrote:
> Hallo Nils,
>
> Nils Lange wrote:
>
>>>> Im Eisfair 1 sind zwei Netzwerkkarten eingebaut und er dient als Router.
>>>> Die Konfiguration ist wie folgt:
>>>>
>>>> Network:  Card-1: Intel 82574L Gigabit Network Connection driver: e1000e
>>>>            IF: eth1 state: up speed: 1000 Mbps duplex: full
>>>>            mac: 68:05:ca:1d:91:f3
>>>>
>>>> Card-2: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet
>>>> Controller
>>>>             driver: r8168
>>>>             IF: eth0 state: up speed: 1000 Mbps duplex: full
>>>>             mac: c4:6e:1f:05:a3:39
>>>
>>> Bitte liefere mal folgende Infos:
>>>
>>> Inhalt von /sys/class/net/eth0/address
>>
>> mail # cat /sys/class/net/eth0/address
>> 68:05:ca:1d:91:f3
>>
>> mail # cat /sys/class/net/eth1/address
>> c4:6e:1f:05:a3:39
>>
>>> Inhalt von /sys/class/net/eth0/device/uevent
>>
>> mail # cat /sys/class/net/eth0/device/uevent
>> DRIVER=e1000e
>> PCI_CLASS=20000
>> PCI_ID=8086:10D3
>> PCI_SUBSYS_ID=8086:A01F
>> PCI_SLOT_NAME=0000:02:00.0
>> MODALIAS=pci:v00008086d000010D3sv00008086sd0000A01Fbc02sc00i00
>>
>> mail # cat /sys/class/net/eth1/device/uevent
>> DRIVER=r8168
>> PCI_CLASS=20000
>> PCI_ID=10EC:8168
>> PCI_SUBSYS_ID=7470:3468
>> PCI_SLOT_NAME=0000:03:00.0
>> MODALIAS=pci:v000010ECd00008168sv00007470sd00003468bc02sc00i00
>>
>>
>>> Nun das gleiche für eth1 statt eth0
>>>
>>> Ausgabe des Befehls:
>>>
>>> lspci -nn | grep Ethernet
>>
>> mail # lspci -nn | grep Ethernet
>> 02:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit
>> Network Connection [8086:10d3]
>> 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
>> RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168]
>> (rev 06)
>
> Ok, mit welchen Einstellungen in der Base-Konfiguration für ETH_X_... hast
> Du diese Werte ermittelt.
>

Das habe ich gerade eben mit diesen Werten gemacht:

IP_ETH_N='2'                      # number of ip ethernet networks

IP_ETH_1_NAME='eth0'                  # optional: other device name than 
ethX
IP_ETH_1_IPADDR='192.168.152.2'  # IP address of your n'th ethernet card
IP_ETH_1_NETWORK='192.168.152.0' # network of your LAN
IP_ETH_1_NETMASK='255.255.255.0'
                                   # netmask of your LAN
IP_ETH_1_MACADDR='68:05:ca:1d:91:f3'
                                   # Mac address of your n'th ethernet card

IP_ETH_2_NAME='eth1'                  # optional: other device name than 
ethX
IP_ETH_2_IPADDR='130.180.18.110'   # IP address of your n'th ethernet card
IP_ETH_2_NETWORK='130.180.18.108'  # network of your LAN
IP_ETH_2_NETMASK='255.255.255.252'  # netmask of your LAN
IP_ETH_2_MACADDR='c4:6e:1f:05:a3:39'