[Eisfair] top 100% Auslastung
Friedhold Schuster
f.schuster at gmx.de
Do Mai 19 18:13:00 CEST 2016
Am 19.05.2016 um 15:09 schrieb Thomas Zweifel:
> Die SMART-Werte wären jetzt definitiv sehr hilfreich.
-------------------------------------------------------------------------------------------------------
smartctl --all /dev/sde
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA200
Serial Number: 63EJ50KKS
Firmware Version: MX4OABB0
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu May 19 18:06:45 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (14726) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 246) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 098 098 054 Pre-fail
Offline - 311
3 Spin_Up_Time 0x0007 119 119 024 Pre-fail
Always - 323 (Average 315)
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 55
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail
Always FAILING_NOW 2005
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 126 126 020 Pre-fail
Offline - 32
9 Power_On_Hours 0x0012 098 098 000 Old_age
Always - 20482
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 55
192 Power-Off_Retract_Count 0x0032 096 096 000 Old_age Always
- 5342
193 Load_Cycle_Count 0x0012 096 096 000 Old_age Always
- 5342
194 Temperature_Celsius 0x0002 166 166 000 Old_age Always
- 36 (Lifetime Min/Max 3/52)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always
- 2472
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
------------------------------------------------------------------------------------------------------------------
eis1 # smartctl --all /dev/sdd
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM001-1CH164
Serial Number: W1E46E32
Firmware Version: CC44
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu May 19 18:07:42 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 575) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 213) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 108 099 006 Pre-fail
Always - 15372456
3 Spin_Up_Time 0x0003 099 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 140
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail
Always - 4298345493
9 Power_On_Hours 0x0032 076 076 000 Old_age
Always - 21371
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 55
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always
- 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 064 053 045 Old_age Always
- 36 (Lifetime Min/Max 18/41)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 96
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 1855
194 Temperature_Celsius 0x0022 036 047 000 Old_age Always
- 36 (0 3 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age
Offline - 16840566768368
241 Total_LBAs_Written 0x0000 100 253 000 Old_age
Offline - 3636889939
242 Total_LBAs_Read 0x0000 100 253 000 Old_age
Offline - 5794633462
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
------------------------------------------------------------------------------------------------------------
eis1 # smartctl --all /dev/sdc
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM001-1CH164
Serial Number: W1E46E8X
Firmware Version: CC44
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu May 19 18:08:30 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 575) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 221) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 103 099 006 Pre-fail
Always - 5332328
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 72
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail
Always - 8624507158
9 Power_On_Hours 0x0032 076 076 000 Old_age
Always - 21571
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 72
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always
- 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 082 082 000 Old_age Always
- 18
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 063 052 045 Old_age Always
- 37 (Lifetime Min/Max 15/48)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 22
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always
- 221356
194 Temperature_Celsius 0x0022 037 048 000 Old_age Always
- 37 (0 3 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 88
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 88
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age
Offline - 124592706295545
241 Total_LBAs_Written 0x0000 100 253 000 Old_age
Offline - 16609197343
242 Total_LBAs_Read 0x0000 100 253 000 Old_age
Offline - 14553352108
SMART Error Log Version: 1
ATA Error Count: 18 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 18 occurred at disk power-on lifetime: 18157 hours (756 days + 13
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 7d+03:49:52.050 READ DMA EXT
27 00 00 00 00 00 e0 00 7d+03:49:52.049 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 7d+03:49:52.041 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 7d+03:49:52.034 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 7d+03:49:52.033 READ NATIVE MAX ADDRESS EXT
Error 17 occurred at disk power-on lifetime: 18157 hours (756 days + 13
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 7d+03:49:49.118 READ DMA EXT
27 00 00 00 00 00 e0 00 7d+03:49:49.117 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 7d+03:49:49.109 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 7d+03:49:49.101 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 7d+03:49:49.101 READ NATIVE MAX ADDRESS EXT
Error 16 occurred at disk power-on lifetime: 18157 hours (756 days + 13
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 7d+03:49:46.181 READ DMA EXT
27 00 00 00 00 00 e0 00 7d+03:49:46.180 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 7d+03:49:46.172 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 7d+03:49:46.165 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 7d+03:49:46.165 READ NATIVE MAX ADDRESS EXT
Error 15 occurred at disk power-on lifetime: 18157 hours (756 days + 13
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 7d+03:49:43.249 READ DMA EXT
27 00 00 00 00 00 e0 00 7d+03:49:43.248 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 7d+03:49:43.240 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 7d+03:49:43.232 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 7d+03:49:43.232 READ NATIVE MAX ADDRESS EXT
Error 14 occurred at disk power-on lifetime: 18157 hours (756 days + 13
hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 7d+03:49:40.324 READ DMA EXT
27 00 00 00 00 00 e0 00 7d+03:49:40.323 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 7d+03:49:40.315 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 7d+03:49:40.308 SET FEATURES [Set transfer
mode]
27 00 00 00 00 00 e0 00 7d+03:49:40.308 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
------------------------------------------------------------------------------------------------------------
eis1 # smartctl --all /dev/sdb
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA200
Serial Number: 63EJ23GGS
Firmware Version: MX4OABB0
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu May 19 18:09:59 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (15013) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 251) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 139 139 054 Pre-fail
Offline - 71
3 Spin_Up_Time 0x0007 128 128 024 Pre-fail
Always - 316 (Average 275)
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 72
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail
Always - 122
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail
Offline - 33
9 Power_On_Hours 0x0012 097 097 000 Old_age
Always - 21813
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 72
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 1189
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always
- 1189
194 Temperature_Celsius 0x0002 176 176 000 Old_age Always
- 34 (Lifetime Min/Max 3/50)
196 Reallocated_Event_Count 0x0032 094 094 000 Old_age Always
- 280
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 88
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 24
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--------------------------------------------------------------------------------------
Mehr Informationen über die Mailingliste Eisfair