[Eisfair] initrd wird beim ?==?utf-8?Q?Boot nicht abgearbeitet
Lutz Spindler
fraenzi2000 at web.de
Mi Jan 6 18:14:32 CET 2016
Hallo zusammen,
mache hier mal einen neuen Tread zu einem alten Thema auf.
Treiber der initrd werden nicht geladen - siehe Thread: Fritz usb 2.1
http://forum.nettworks.org/index.php?t=msg&th=6630&start=0&
ich vermute, das die initrd nicht richtig abgearbeitet oder geladen
wird.
hier die Bootausgabe, die ich über die Serielle Konsole sehe
Restarting system.
PC Engines ALIX.2 v0.99h
640 KB Base Memory
261120 KB Extended Memory
01F0 Master 045A SFCF1024H1BK1TO-I-MS-553-SMA
Phys C/H/S 1986/16/63 Log C/H/S 993/32/63
LILO 24.1 boot:
Loading eis.................................
..................................
........
BIOS data check successful
Initializing cgroup subsys cpu
Linux version 3.2.71-eisfair-1-SMP (root at kernel32) (gcc version 4.7.4
(GCC) ) #1
SMP Tue Oct 13 23:44:10 CEST 2015
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU!
DMI not present or invalid.
last_pfn = 0x10000 max_arch_pfn = 0x100000
init_memory_mapping: 0000000000000000-0000000010000000
RAMDISK: 0fe57000 - 10000000
ACPI Error: A valid RSDP was not found (20110623/tbxfroot-220)
0MB HIGHMEM available.
256MB LOWMEM available.
mapped low ram: 0 - 10000000
low ram: 0 - 10000000
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x00010000
HighMem empty
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x000000a0
0: 0x00000100 -> 0x00010000
Using APIC driver default
SMP: Allowing 1 CPUs, 0 hotplug CPUs
No local APIC present or hardware disabled
APIC: disable apic facility
APIC: switched to apic NOOP
Allocating PCI resources starting at 10000000 (gap: 10000000:eff00000)
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @cfc48000 s24320 r0 d20736 u45056
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
64912
Kernel command line: auto BOOT_IMAGE=eis ro root=302 kdb_reset
console=ttyS0,384
00n8 apm=power-off raid=noautodetect
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Initializing CPU#0
Initializing HighMem for node 0 (00000000:00000000)
Memory: 252672k/262144k available (3053k kernel code, 9024k reserved,
1213k data
, 404k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
.init : 0xc142b000 - 0xc1490000 ( 404 kB)
.data : 0xc12fb464 - 0xc142a940 (1213 kB)
.text : 0xc1000000 - 0xc12fb464 (3053 kB)
Checking if this processor honours the WP bit even in supervisor
mode...Ok.
SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:2304 nr_irqs:256 16
Console: colour dummy device 80x25
console [ttyS0] enabled
Fast TSC calibration using PIT
Detected 498.006 MHz processor.
Calibrating delay loop (skipped), value calculated using timer
frequency.. 996.0
1 BogoMIPS (lpj=1992024)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
SMP alternatives: switching to UP code
Freeing SMP alternatives: 20k freed
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Performance Events: no PMU driver, software events only.
Brought up 1 CPUs
Total of 1 processors activated (996.01 BogoMIPS).
xor: measuring software checksum speed
8regs : 394.000 MB/sec
8regs_prefetch: 333.000 MB/sec
32regs : 203.000 MB/sec
32regs_prefetch: 208.000 MB/sec
pII_mmx : 864.000 MB/sec
p5_mmx : 679.000 MB/sec
xor: using function: pII_mmx (864.000 MB/sec)
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfced9, last bus=0
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
raid6: int32x1 51 MB/s
raid6: int32x2 61 MB/s
raid6: int32x4 62 MB/s
raid6: int32x8 64 MB/s
raid6: mmxx1 153 MB/s
raid6: mmxx2 234 MB/s
raid6: sse1x1 152 MB/s
raid6: sse1x2 231 MB/s
raid6: using algorithm sse1x2 (231 MB/s)
ACPI: Interpreter disabled.
vgaarb: loaded
PCI: Probing PCI hardware
Switching to clocksource pit
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: PnP BIOS support was not detected.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 1700k freed
platform rtc_cmos: registered platform RTC device (no PNP device found)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block/inode
numbers, no
debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 496
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
Switching to clocksource tsc
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
floppy0: no floppy controllers found
brd: module loaded
Uniform Multi-Platform E-IDE driver
cs5536 0000:00:0f.2: IDE controller (0x1022:0x209a rev 0x01)
cs5536 0000:00:0f.2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07
hda: SFCF1024H1BK1TO-I-MS-553-SMA, CFA DISK drive
hda: host side 80-wire cable detection failed, limiting max speed to
UDMA33
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
amd74xx 0000:00:0f.2: UDMA100 controller
amd74xx 0000:00:0f.2: IDE controller (0x1022:0x209a rev 0x01)
cs5536 0000:00:0f.2: BAR 0: can't reserve [io 0x01f0-0x01f7]
amd74xx 0000:00:0f.2: can't reserve resources
ide-gd driver 1.18
hda: max request size: 128KiB
hda: 2001888 sectors (1024 MB) w/0KiB Cache, CHS=1986/16/63
hda: cache flushes supported
hda: hda1 hda2
i8042: PNP: No PS/2 controller found. Probing ports directly.
i8042: No controller found
mousedev: PS/2 mouse device common for all mice
rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, 114 bytes nvram
Linux telephony interface: v1.00
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
mailto:dm-devel at redhat.com
cpuidle: using governor ladder
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
Using IPI No-Shortcut mode
rtc_cmos rtc_cmos: setting system clock to 2015-12-23 20:09:54 UTC
(1450901394)
md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
EXT3-fs (hda2): error: couldn't mount because of unsupported optional
features (
240)
EXT2-fs (hda2): error: couldn't mount because of unsupported optional
features (
240)
EXT4-fs (hda2): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) readonly on device 3:2.
Freeing unused kernel memory: 404k freed
Write protecting the kernel text: 3056k
Write protecting the kernel read-only data: 1044k
INIT: version 2.89 booting
Running /etc/init.d/boot
EXT4-fs (hda2): re-mounted. Opts: errors=remount-ro
Checking file systems...
fsck from util-linux 2.23.1
/dev/hda2: clean, 24705/58880 files, 127021/235127 blocks
/dev/hda1: clean, 19/12288 files, 16088/49152 blocks
EXT4-fs (hda2): re-mounted. Opts: errors=remount-ro
mount: could not open /etc/mtab - using /proc/mounts instead
mount: proc already mounted on /proc
EXT4-fs (hda1): mounted filesystem with ordered data mode. Opts:
errors=remount-
ro
/dev/hda1 on /boot type ext4 (rw,errors=remount-ro)
devpts on /dev/pts type devpts (rw)
/sys on /sys type sysfs (rw)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev)
EXT4-fs (hda2): re-mounted. Opts: errors=remount-ro,acl,user_xattr
INIT: Entering runlevel: 2
* Running /etc/init.d/rc ...
* Switching from runlevel N to 2 ...
* Setting console mode to Unicode (UTF-8)... [
OK ]
* Setting up hostname ... [
OK ]
* Loading kernel modules ...
apm: BIOS not found.
modprobe: FATAL: Module reboot=bios not found.
modprobe: FATAL: Module nokbd not found.
modprobe: FATAL: Module powermanagement not found. [
OK ]
* Loading ide cdrom drivers ...
ide-cd driver 5.00 [
OK ]
* Configuring loopback and ethernet device ... [
OK ]
* Starting usb ...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb [
OK ]
* Loading ethernet drivers ...
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
via-rhine 0000:00:09.0: eth0: VIA Rhine III (Management Adapter) at
0x11000, 00:
0d:b9:17:ef:98, IRQ 10
via-rhine 0000:00:09.0: eth0: MII PHY found at address 1, status 0x786d
advertis
ing 05e1 Link c5e1
via-rhine 0000:00:0a.0: eth1: VIA Rhine III (Management Adapter) at
0x11400, 00:
0d:b9:17:ef:99, IRQ 11
via-rhine 0000:00:0a.0: eth1: MII PHY found at address 1, status 0x7849
advertis
ing 05e1 Link 0000
via-rhine 0000:00:0b.0: eth2: VIA Rhine III (Management Adapter) at
0x11800, 00:
0d:b9:17:ef:9a, IRQ 15
via-rhine 0000:00:0b.0: eth2: MII PHY found at address 1, status 0x7849
advertis
ing 05e1 Link 0000
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <mailto:becker at scyld.com>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder [
OK ]
* Configuring ip on ethernet cards ...
via-rhine 0000:00:09.0: eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1[
OK ]
* Setting up additional routes ... [
OK ]
* Setting up resolv.conf ... [
OK ]
* Starting syslogd ... [
OK ]
* Starting klogd ... [
OK ]
* Starting Xinetd daemon ... [
OK ]
* Starting OpenSSH daemon ... [
OK ]
* Starting atd ... [
OK ]
* Starting cron ... [
OK ]
starting SMTP server ...
starting fetchmail daemon ...
enabling pop3 daemon ...
enabling imap4 daemon ...
* Starting CAPI services ... [
OK ]
Detecting ISDN-Devices ...
* Starting LPRng ...
- Starting lpd ... [
OK ]
* Starting Samba ...
- Starting nmbd ... [
OK ]
- Starting smbd ... [
OK ]
* Starting Smbfs ... [
OK ]
* Starting Mini_HTTPD-Webserver ... [
OK ]
* Starting EisFAX ...
add cron job.
im Gegensatz zum Thread "Eisfair 1 auf ZOTAC CI323" bootet der ALIX aber
durch.
http://forum.nettworks.org/index.php?t=msg&th=6741&start=0&
die fehlenden Module
ohci_hcd
ehci_hcd
habe ich dann in der Base eingetragen, dann werden sie auch geladen.
vielen Dank
viele Grüße
Lutz
Mehr Informationen über die Mailingliste Eisfair