[Eisfair] E-1: SN keine Gruppenliste.
Kay Martinen
kay at martinen.de
Sa Mär 1 16:51:51 CET 2014
Am 01.03.2014 16:36, schrieb Kay Martinen:
> Am 01.03.2014 16:10, schrieb Marcus Roeckrath:
>>> -rw-r--r-- 1 news news 602319 Feb 28 23:00 grouplist
>
>> Deine Platte ist in Ordnung?
eisfair # smartctl --all /dev/hda
smartctl 5.39 2009-12-09 r2995 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 60 family
Device Model: Maxtor 5T020H2
Serial Number: T2HBTH6C
Firmware Version: TAH71DP0
User Capacity: 20,491,075,584 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0
Local Time is: Sat Mar 1 16:45:41 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 30) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 14) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000a 253 252 000 Old_age
Always - 1521
3 Spin_Up_Time 0x0027 223 211 063 Pre-fail
Always - 11735
4 Start_Stop_Count 0x0032 253 253 000 Old_age
Always - 1447
5 Reallocated_Sector_Ct 0x0033 249 249 063 Pre-fail
Always - 11
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail
Offline - 0
7 Seek_Error_Rate 0x000a 253 250 000 Old_age
Always - 0
8 Seek_Time_Performance 0x0027 249 246 187 Pre-fail
Always - 58083
9 Power_On_Minutes 0x0032 250 250 000 Old_age
Always - 94h+57m
10 Spin_Retry_Count 0x002b 251 232 223 Pre-fail
Always - 2
11 Calibration_Retry_Count 0x002b 253 251 223 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 246 246 000 Old_age
Always - 2844
196 Reallocated_Event_Count 0x0008 240 240 000 Old_age
Offline - 13
197 Current_Pending_Sector 0x0008 252 251 000 Old_age
Offline - 1
198 Offline_Uncorrectable 0x0008 253 252 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 198 000 Old_age
Offline - 1
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 249 224 000 Old_age Always
- 4214
202 Data_Address_Mark_Errs 0x000a 253 252 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
- 74
204 Soft_ECC_Correction 0x000a 253 252 000 Old_age Always
- 0
205 Thermal_Asperity_Rate 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 252 240 000 Old_age Always
- 1
208 Spin_Buzz 0x002a 253 246 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 221 220 000 Old_age
Offline - 0
96 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
97 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
98 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 4778 inconsistent with error log pointer 5
ATA Error Count: 4778 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4778 occurred at disk power-on lifetime: 1113 hours (46 days + 9
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 25d+14:31:36.912 IDENTIFY PACKET DEVICE
c4 ff 01 01 00 00 a0 08 25d+14:31:36.896 READ MULTIPLE
b0 d2 00 00 4f c2 a0 08 25d+14:31:36.864 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 25d+14:31:36.816 SMART ENABLE OPERATIONS
91 ff 3f 00 00 00 af 08 25d+14:31:36.816 INITIALIZE DEVICE
PARAMETERS [OBS-6]
Error 4777 occurred at disk power-on lifetime: 1113 hours (46 days + 9
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 05 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 05 01 00 00 a0 08 25d+14:31:32.672 IDENTIFY PACKET DEVICE
ca 00 08 18 94 8a e0 08 25d+14:30:06.464 WRITE DMA
ca 00 68 b0 93 8a e0 08 25d+14:30:06.464 WRITE DMA
ca 00 08 98 26 77 e0 08 25d+14:30:06.432 WRITE DMA
ca 00 02 02 08 00 e0 08 25d+14:30:06.432 WRITE DMA
Error 4776 occurred at disk power-on lifetime: 1113 hours (46 days + 9
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:03:37.408 IDENTIFY PACKET DEVICE
c4 ff 01 01 00 00 a0 08 00:03:37.408 READ MULTIPLE
b0 d2 00 00 4f c2 a0 08 00:03:37.376 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:03:37.344 SMART ENABLE OPERATIONS
91 ff 3f 00 00 00 af 08 00:03:37.344 INITIALIZE DEVICE
PARAMETERS [OBS-6]
Error 4775 occurred at disk power-on lifetime: 1113 hours (46 days + 9
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 05 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 05 01 00 00 a0 00 00:03:33.200 IDENTIFY PACKET DEVICE
Error 4774 occurred at disk power-on lifetime: 1113 hours (46 days + 9
hours)
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 ff 00 01 00 00 a0 08 00:06:54.032 IDENTIFY PACKET DEVICE
c4 ff 01 01 00 00 a0 08 00:06:54.032 READ MULTIPLE
b0 d2 00 00 4f c2 a0 08 00:06:53.984 SMART ENABLE/DISABLE
ATTRIBUTE AUTOSAVE
b0 d8 3f 00 4f c2 a0 08 00:06:53.952 SMART ENABLE OPERATIONS
91 ff 3f 00 00 00 af 08 00:06:53.952 INITIALIZE DEVICE
PARAMETERS [OBS-6]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1113
-
# 2 Short offline Completed without error 00% 1113
-
# 3 Short offline Completed without error 00% 1113
-
# 4 Short offline Completed without error 00% 1113
-
# 5 Short offline Completed without error 00% 1113
-
# 6 Short offline Completed without error 00% 1113
-
# 7 Short offline Completed without error 00% 1113
-
# 8 Short offline Completed without error 00% 1113
-
# 9 Extended offline Completed without error 00% 1113
-
#10 Short offline Completed without error 00% 1113
-
#11 Short offline Completed without error 00% 1113
-
#12 Short offline Completed without error 00% 1113
-
#13 Short offline Completed without error 00% 1113
-
#14 Short offline Completed without error 00% 1113
-
#15 Short offline Completed without error 00% 1113
-
#16 Short offline Completed without error 00% 1113
-
#17 Extended offline Completed without error 00% 1113
-
#18 Short offline Completed without error 00% 1113
-
#19 Short offline Completed without error 00% 1113
-
#20 Short offline Completed without error 00% 1113
-
#21 Short offline Completed without error 00% 1113
-
Device does not support Selective Self Tests/Logging
Die fehlerlog einträge sind mir noch etwas unerklärlich, aber insgesamt
scheint smart keine fehler zu sehen. Oder?
>> Vielleicht mal Filesystemcheck machen?
>
> Mache ich im anschluß mal.
... wenn ich jetzt noch wüsste wie. Unmounten kann ich / nicht also muss
es beim booten sein. Wie komme ich beim EIS in den single-user mode um
ein e2fsck zu starten?
Kay
Mehr Informationen über die Mailingliste Eisfair