[Fli4l_dev] Informationen zu den wöchentlichen 4.0-Archiven vom 24.03.2017 (r47533)

Sebastian Klein fli4l at wysiwyng.de
Sa Apr 1 17:20:40 CEST 2017


Moin Boris,

Am 31.03.17 um 16:45 schrieb B. Sprenger:

>>> Letzte Idee die ich noch habe ist der Whitelist-Eintrag, evtl.
>>>  stört der ja...
> 
> 
> Ich habe gerade wieder r47528 trunk aufgespielt, den igmp gekilled und
> die igmpproxy.conf wie folgt geändert:
> Zeile mit altnet 239.35.0.0/16 auskommentiert.
> 
> # imgpproxy.conf for OPT_IGMPPROXY package
> # This script is built automatically
> #
> quickleave
> # configure upstream
> phyint eth1.8 upstream ratelimit 0 threshold 1
> # #         altnet 239.35.0.0/16
>          altnet 217.0.119.0/24
>          altnet 193.158.34.0/23
> # configure downstream
> phyint eth2 downstream ratelimit 0 threshold 1
>          whitelist 239.35.0.0/16
> # configure disabled interface
> phyint lo disabled
> phyint eth0 disabled
> phyint eth1 disabled
> phyint eth1.7 at eth1 disabled
> phyint eth1.8 at eth1 disabled
> phyint dummy0 disabled
> phyint ppp1 disabled

Hehe ich meinte genau anders rum, also die "altnet 239...." drin lassen
aber unten die "whitelist 239..." raus. Und auch die "@eth1" nimm
nochmal raus.

> Die Logdatei sieht daraufhin so aus:
> igmpproxy[10811]: Searching for config file at '/etc/igmpproxy.conf'
> igmpproxy[10811]: Config: Quick leave mode enabled.
> igmpproxy[10811]: Config: Got a phyint token.
> igmpproxy[10811]: Config: IF: Config for interface eth1.8.
> igmpproxy[10811]: Config: IF: Got upstream token.
> igmpproxy[10811]: Config: IF: Got ratelimit token '0'.
> igmpproxy[10811]: Config: IF: Got threshold token '1'.
> igmpproxy[10811]: Config: IF: Got altnet token 217.0.119.0/24.
> igmpproxy[10811]: Config: IF: Altnet: Parsed altnet to 217.0.119/24.
> igmpproxy[10811]: Config: IF: Got altnet token 193.158.34.0/23.
> igmpproxy[10811]: Config: IF: Altnet: Parsed altnet to 193.158.34/23.
> igmpproxy[10811]: IF name : eth1.8
> igmpproxy[10811]: Next ptr : 0
> igmpproxy[10811]: Ratelimit : 0
> igmpproxy[10811]: Threshold : 1
> igmpproxy[10811]: State : 1
> igmpproxy[10811]: Allowednet ptr : 9d9e2b0
> igmpproxy[10811]: Config: Got a phyint token.
> igmpproxy[10811]: Config: IF: Config for interface eth2.
> igmpproxy[10811]: Config: IF: Got downstream token.
> igmpproxy[10811]: Config: IF: Got ratelimit token '0'.
> igmpproxy[10811]: Config: IF: Got threshold token '1'.
> igmpproxy[10811]: Config: IF: Got whitelist token 239.35.0.0/16.
> igmpproxy[10811]: Config: IF: Altnet: Parsed altnet to 239.35/16.
> igmpproxy[10811]: IF name : eth2
> igmpproxy[10812]: select() failure; Errno(14): Bad address
> igmpproxy[10812]: select() failure; Errno(14): Bad address

wo bekommt der eth2 her?

> Die "fehlerhafte" Adresse wandert jetzt.
> Wie sieht denn die Logdatei von jemand aus, bei dem das funktioniert?

Gute Frage ich stochere ja nur im blauen Dunst rum, da ich kein
T-Offline habe...

Kann dir auch die nächste Woche nicht wirklich weiter helfen (sofern ich
noch Ideen entwickeln würde), da ich im Urlaub bin...

-- 
Grüße,
Sebastian
[fli4l-team]



Mehr Informationen über die Mailingliste Fli4l_dev